
Free Hydraulic
Calculators
Calculate hydraulic flow rate, tube bore size, fluid velocity and hydraulic power using Lister Fluid Power’s free hydraulic calculators.
​
These tools help engineers, designers and maintenance professionals perform common hydraulic system calculations using flow rate, pressure, cylinder dimensions and fluid line measurements.
​
Choose a calculator to suit your requirement:
​​
​
Determine the flow required to extend or retract a hydraulic cylinder within a specified time.
Calculate the required tube internal diameter based on flow rate and target fluid velocity.
​
Check the fluid velocity inside a hydraulic pipe or tube to help assess system efficiency and pressure losses.
​
​
Calculate hydraulic power in kW and HP using system pressure and flow rate.
​
Each calculator includes the required inputs, calculation method and units to help you understand the result and apply it to your hydraulic system.​
​
These calculators only provide initial engineering calculations. Final component selection should also consider operating conditions, pressure losses, duty cycle, fluid properties and the requirements of the complete hydraulic system.
Hydraulic Cylinder Flow Rate Calculator
Calculate the hydraulic flow rate required to extend and retract a hydraulic cylinder within a specified time.
​
Our Hydraulic Cylinder Flow Rate Calculator uses the cylinder bore diameter, piston rod diameter, stroke length and desired movement times to determine the required flow rate in litres per minute (L/min) for both extension and retraction.
Whether you are sizing a hydraulic pump, selecting control valves or checking cylinder cycle times, this calculator helps you determine the flow required to achieve your target operating speed.
How to use:
​
-
Enter your cylinder dimensions:
Bore Diameter (mm)
Rod Diameter (mm)
Stroke Length (mm)
-
Enter your desired cycle times for:
Extension Time (seconds)
Retraction Time (seconds)
-
Click “Calculate Flow Rates”
-
The tool will display the flow rates (L/min) needed to meet your timing requirements for both extension and retraction.
​
Calculating the required flow rate helps you:
​
-
Select a hydraulic pump with sufficient flow capacity.
-
Determine the flow required to achieve target cylinder cycle times.
-
Match hydraulic valves and other components to system requirements.
-
Avoid excessive flow that can increase energy consumption and heat generation.
-
Improve hydraulic system productivity and efficiency.
How Hydraulic Cylinder Flow Rate is Calculated
The required flow rate depends on the volume of fluid needed to move the cylinder through its stroke and the time allowed for that movement.
​
Extension flow rate:
Q = (π × D² ÷ 4) × L ÷ t
Retraction flow rate:
Q = [π × (D² − d²) ÷ 4] × L ÷ t
​
Where:
-
Q = required flow rate
-
D = cylinder bore diameter
-
d = piston rod diameter
-
L = cylinder stroke length
-
t = extension or retraction time
​
When dimensions are entered in millimetres and time in seconds, the calculator converts the result into litres per minute (L/min).
Bore Size Calculator
Find the Right Tube for Your Hydraulic Needs
Correct tube sizing is crucial to ensure optimal flow and minimize pressure drops in hydraulic systems. Our Tube Size Calculator helps you determine the appropriate tube bore size based on your flow rate and desired velocity. This ensures your system runs efficiently and safely.​
How to use:
​
-
Enter the flow rate in L/min.
-
Select the line type from the dropdown menu.
-
Enter the velocity (within the suggested range for the selected line type).
-
Click Calculate Tube Bore to get the result.
​
Benefits:
​
-
Prevent under sizing or oversizing of tubes.
-
Reduce energy loss and improve system performance.
-
Increase the lifespan of your hydraulic components.
Velocity Calculator
Ensure Optimal Fluid Velocity for Your System
Maintaining the right fluid velocity in hydraulic lines is essential to avoid turbulence, noise, and wear. Our Velocity Calculator allows you to calculate fluid velocity based on flow rate and tube diameter, ensuring you stay within the recommended ranges for different line types.
How to use:
​
-
Enter the flow rate in L/min.
-
Input the inside diameter (ID) of the tube in mm.
-
Hit "Calculate Velocity" to get fluid velocity in metres per second (m/s).
​
Benefits:
​
-
Optimize hydraulic line performance.
-
Prevent premature system failure due to incorrect velocities.
-
Ensure compliance with industry standards.
Power (KW & HP) Calculator
Accurately Calculate Hydraulic Power Requirements
Understanding the power required for your hydraulic system is critical for selecting the right components and maintaining energy efficiency. Our KW & HP Calculator lets you convert hydraulic pressure and flow rate into kilowatts (KW) and horsepower (HP) with ease.
How to use:
​
-
Enter the pressure in Bar. This is the force applied by the fluid in the system.
-
Enter the flow rate in Litres per Minute (L/min). This is the amount of fluid moving through the system.
-
Press the "Calculate Power" button to see the results.
​
Benefits:
​
-
Optimise motor and pump selection.
-
Improve energy efficiency and reduce operating costs.
-
Avoid underpowered or overpowered systems.
Finding our hydraulic calculators effective? Why not try our Pneumatic Calculators as well! Explore now and take your pneumatic system optimisation to the next level.

We’re your partner in
hydraulic success
Explore our Knowledge Hub for more valuable resources, technical guides, case studies and insights from our experts.